
Image alt text: Driver holding a Smart Start blow box handset at the steering wheel before giving a breath sample
“Blow box” is the everyday Canadian name for an ignition interlock device, a breath screening device wired to your vehicle’s ignition. You give a breath sample before the engine starts, then rolling tests and rolling re-tests while you drive. A clean sample needs a deep breath, a steady blow and a clean mouth.
An aborted sample traces back to technique: blowing before the prompt, blowing too hard or too softly, or water left in your mouth. You can control that before you pick up the handset.
What a Blow Box Is and Where It Sits
The blow box is a small handheld unit with a mouthpiece, a tri-coloured LCD display and a numeric keypad. It’s located near the driver’s seat and connected to the engine’s ignition system, so you can reach it without leaving your seat. The keypad also lets you call up the date and time of your next appointment.

Image alt text: Driver seated behind the wheel with a blow box handset mounted on the dashboard near the driver’s seat
The device controls one thing: whether the engine can start. It can’t turn off an engine that’s already running, so a missed or failed rolling test won’t stall the vehicle in traffic. It does keep a log. Every test result is recorded, along with engine starts and stops, disconnections and any tampering, and that record goes to your provincial monitoring authority as your ignition interlock report.
Inside the handset, the ignition interlock’s fuel cell sensor measures alcohol on your breath. The sensor is alcohol-specific, so mouthwash or another product with alcohol in it can show up in a sample even when you haven’t had a drink.
In Yukon’s interlock program and in Quebec, the blow box can be paired with an optional Photo ID camera (about one cubic inch) mounted on the driver’s side window.. It takes a picture at each test so the record shows who gave the sample. The Photo ID camera option isn’t available anywhere else.
How to Give a Clean Blow Box Sample, Step by Step
The current Smart Start Canada device, the SSI-20/35 series, is blow-only. There’s no hum step, so a good sample depends on timing and a steady breath. You’ll get blow training at your installation appointment.

Image alt text: Driver giving a steady breath sample into the mouthpiece of an ignition interlock handset
Here’s how to blow into an interlock so the handset accepts the sample:
- Rinse your mouth with water. Do it before every test, then swallow or spit so no water is left in your mouth. Water left behind adds moisture to the handset.
- Take a deep breath immediately before the test.
- Wait for BLOW on the screen. Blowing early, or breathing in close to the mouthpiece, gives you an abort.
- Blow steadily until the test ends. Keep an even, moderate pressure from start to finish rather than one hard puff. Stopping partway gives the handset too little air to read.
A small bottle of water kept in the vehicle makes the rinse easy before a rolling test, when you’re away from a tap.
Cold weather adds a step. Warm-up is brief in normal conditions but takes longer when the handset is cold, so leave a few extra minutes before you need to drive on a winter morning. The cold-weather tips for interlock users cover warm-up, the battery and the mouthpiece.
Reading the Screen: PASS, WARN, FAIL and VIOL
After each sample, the display shows one of four results, and each one tells you whether the engine will start:
| Screen | What the device detected | Can you start the vehicle? |
|---|---|---|
| PASS | No alcohol | Yes |
| WARN (Alberta Only) | Low alcohol | Yes |
| FAIL | Alcohol | No |
| VIOL | High alcohol | No |
After any result other than PASS, take a follow-up test as soon as the device is ready for one. After a FAIL, the screen cycles from FAIL to WAIT with a countdown, then back to BLOW. Use the countdown: rinse with water, air out the vehicle if a product in the car could be the cause, and give a fresh sample when BLOW appears. Every result, including the follow-up, is recorded for your monitoring authority.
Aborted Tests Aren’t Violations
An abort means the handset couldn’t read the sample, so it measured nothing. The screen shows a prompt that names the problem:
- Blow Softer: the device detected too much air pressure. Ease off and blow more gently.
- Blow Longer: the device didn’t detect enough air, or you stopped early. Increase the air flow and keep blowing for the whole test.
- Don’t Inhale: air moved the wrong way through the handset, usually because you blew before BLOW appeared or breathed in close to the mouthpiece.
- Please Retry: moisture built up inside the handset from repeated testing, or the vent on the handset is covered. Give it time to clear the moisture, and uncover the vent.
An aborted test isn’t a violation. Take the test again once the screen shows BLOW.
Several aborts in a row can put the handset into a temporary lockout, and it won’t accept a test until it resets. A temporary lockout can happen before you start the vehicle or after. Use the wait to drink some water, take a few deep breaths and air out the vehicle, and leave the handset connected the whole time. Test again when the device resets.
Rolling Tests and Rolling Re-Tests While You Drive
A passing start doesn’t end the testing. Once the engine is running, the blow box makes breath sample requests at random intervals, and these in-drive samples are called rolling tests and rolling re-tests. A request asks you to give a breath sample while the engine keeps running, which is how a rolling re-test in Ontario works.

Image alt text: Open highway with a double yellow centre line, where rolling tests and rolling re-tests take place
When a request comes in, a timer starts. Find a safe place to pull over, then give the sample the same way you did at start-up: deep breath, wait for BLOW, steady blow. If you haven’t responded by the halfway point of the timer, the vehicle’s horn sounds as a reminder. A missed rolling test is recorded as a violation and starts a countdown on the device, so answer every request.
A few habits keep rolling tests from turning into missed tests:
- Check the screen before you switch off. If a test is pending when you reach your destination, complete it before you leave the vehicle. You can still finish a test after turning off the engine, but you’ll have less time and the device beeps faster as the time runs out.
- Every driver tests. Anyone who drives the vehicle has to complete the rolling tests, and you’re responsible for all breath samples recorded on your device, whoever gave them. Show anyone who borrows the vehicle how the handset works before they drive.
- The sample has to come from the driver. If you’re the one driving, letting a passenger blow for you is a program violation.
- Smart IDLE, if applicable. Smart IDLE is an optional feature that lets a parked vehicle run for up to 8 hours without rolling test requests. After a passing start, look for the asterisk in the corner of the screen, press #7, and the display reads IDLE 8:00. Rolling tests pause until the timer reaches 0:00, you start moving, or you press #7 again, and the device asks for a test as soon as Smart IDLE ends.
What Can Throw Off a Blow Box Sample
Plenty of products you use every day contain alcohol, and their fumes stay in a closed car. Because the sensor is alcohol-specific, it reads that alcohol the same way it reads alcohol from a drink. What people call false positives on an interlock are real readings of alcohol from a product, and they usually clear once you rinse with water and wait a few minutes.
Keep strong-smelling products away from the handset, and ask passengers not to spray or apply them in the vehicle before a test. If you get a WARN or FAIL that you believe came from a product, rinse your mouth with water while you air out the vehicle, then take the next available test.
After a fail or any other violation, complete an occurrence report explaining what happened, if applicable in your province (Alberta is excluded). How the blow box in Alberta fits the rest of the provincial program is covered in its own guide. You file it in the Manage Your Account section of your Smart Start Canada account, and your monitoring authority can read it directly. The provincial authority reviews the device record and decides what follows, so contact that authority with any question about how a result is handled.
Caring for the Handset
A handset that’s looked after warms up faster and gives fewer technical problems.

Image alt text: Driver clearing frost from a windshield in a snowy Canadian driveway on a winter morning
These habits cover most of it:
- Bring it inside. Take the handset indoors when you can. It protects the handset from theft and from the weather. In deep cold or heat, handset care in extreme weather means disconnecting the handset and bringing it indoors, which cuts the warm-up time and helps avoid technical issues when you get back in the vehicle.
- Keep the vent clear. A covered vent can trap moisture and trigger a Please Retry abort.
- Disconnect it at the right time. Disconnecting the handset while the device is on is recorded as a violation. Disconnect it only with the vehicle off and no test pending, and never during a temporary lockout.
- Look after the battery. The device draws little power, but a weak battery or charging system can cause power-fail events from low voltage. A power loss of 15 minutes or longer is recorded as a violation.
- Leave the wiring alone. Call Smart Start Canada at 1-844-432-4776 before anyone touches the device or the vehicle’s electrical system, including a mechanic doing unrelated work.
- Keep your Service appointments. The device is Serviced every 30 to 60 days at a Smart Start Canada service centre, and missing the date starts a Service lockout countdown on the handset.
Blow Box FAQs
What is a blow box?
A blow box is the common Canadian name for an ignition interlock device. It’s a breath-testing handset wired to a vehicle’s ignition that keeps the engine from starting until the driver gives a passing breath sample, then asks for rolling tests and rolling re-tests while the vehicle is running. Each test is recorded for the provincial monitoring authority.
How much does a blow box cost in Alberta?
Costs vary by province and change over time. Check the current Alberta program fees for installation and Service before you book your appointment.
How much is a blow box in Saskatchewan?
Saskatchewan sets its own program, and its costs change from time to time as well. Check the current Saskatchewan program fees for installation and Service before your appointment.
How long do you need a blow box for?
Each province sets the length of its own program, and the term that applies to you comes from the authority that runs your program. In Ontario that’s the Ministry of Transportation (MTO); in Alberta, Alberta Transportation and Economic Corridors; in British Columbia, RoadSafetyBC; in Saskatchewan, SGI; in Manitoba, Manitoba Public Insurance (Driver Fitness); and in Quebec, the SAAQ. Confirm your term with that authority before you book the removal of the device.
See the Blow Box Before Your Installation
Smart Start Canada serves All Provinces from service centres coast to coast and has completed more than 1.1 million installations.

Image alt text: Smart Start Canada support agent wearing a headset, ready to answer blow box questions
Before your appointment, see the blow box and download its user manual, so the screen prompts are familiar when you give your first sample. For anything the manual doesn’t answer, call 1-844-432-4776 in Western and Central Canada or 1-844-282-8300 in Quebec.
Disclaimer: This article provides general information only. Ignition interlock program rules vary by province and territory and change over time. Always confirm current requirements directly with your provincial program authority (the Ontario Ministry of Transportation, Alberta Transportation and Economic Corridors, RoadSafetyBC, SGI, Manitoba Public Insurance or the SAAQ) or Smart Start Canada before making decisions about your enrolment.