Your Smart Start Handset Explained: Keypad Commands, Screen Symbols and Countdown Messages

Smart Start codes are the keypad commands, corner symbols and countdowns on your handset. Press #1 for your appointment date, #2 for the voltages, #3 for violation points left, #7 for Smart IDLE and * to lock the keypad. A * means the engine is running, a + means motion was detected, and a countdown is the time left before a lockout.

It’s 7:40 on a Tuesday, you’re already running late, and a word you’ve never seen is showing on the handset screen. Guessing at that moment is how a minor message becomes a missed appointment. The keypad comes first, because it answers the most questions before a call is ever needed.

Smart Start Codes on the Keypad, Key by Key

The number pad shows information and switches a few commands on and off. Each key does one job, and none of them can change your program or your Service schedule.

#1 shows your appointment date. It’s the date last programmed into the handset. If you change an appointment through Manage Your Account or by phone, the handset keeps showing the old date until your next visit, because the device only learns the new one at the appointment. Keep your own note of the date you booked. The handset catches up the next time it’s Serviced.

#2 shows the voltages. The handset reads the electrical supply it’s getting from the vehicle, and it can do that with the vehicle at rest, with the ignition on or with the engine running. You’ll see a battery reading and an ignition reading, and the site’s frequently asked questions (FAQs) list a minimum of 12 volts for each. A lower number means the battery needs charging or a boost. A weak battery or charging system can cause power-fail violations from low voltage, so a quick #2 check on a cold morning takes a few seconds and can save you a call. It’s also the first reading the call centre will ask for if you phone about a power issue. Don’t touch the wiring yourself. Call 1-844-432-4776 (1-844-282-8300 in Quebec).

Image alt text: Hand pressing a key on the numeric keypad of an ignition interlock handset inside a vehicle

#3 shows your remaining violation points. Most provinces allow only one violation point, so the number you see may be simple. Where your province allows more than one, #3 shows how many missed tests you can still have before the handset goes into a violation lockout. The count resets at every Service, which is one more reason to keep every appointment. Press #1 and #3 at the start of each week and the date and your remaining points won’t catch you off guard.

#7 turns Smart IDLE on or off. It only works when four conditions line up: the engine is running, the vehicle is idling, Smart IDLE has been added to your account and an asterisk shows at the top of the screen. If the asterisk isn’t there, #7 won’t do anything. The Smart IDLE page covers how to add the feature, and it’s optional.

* locks and unlocks the keypad. On its own, the star key locks the pad. Press it again to cycle the lock off. It’s useful when a passenger or a child might lean on the buttons, since an accidental #7 can end Smart IDLE early and bring up a test you weren’t expecting.

The Symbols in the Corner of the Screen

Two small symbols can appear in the corner of the display, and they report what the vehicle is doing right now. A * means the engine is running. A + means the handset has recently detected motion.

You don’t have to act on either one. They’re status indicators and don’t ask you for anything. The asterisk counts in one situation, though. Smart IDLE only accepts #7 once the asterisk has appeared, and after you’ve been driving it can take a few minutes to show up. Come to a complete stop, put the vehicle in Park and give it time. Pressing #7 over and over before the asterisk shows won’t speed it up.

Test Prompts and Results, in Brief

Between the symbols and the keypad, the screen mostly talks to you about breath samples. Each prompt below is one line here, because the blow box post owns the technique and the step-by-step.

Image alt text: Driver taking a deep breath before blowing steadily into an ignition interlock handset held near the steering wheel

The first group tells you where you are in a test and what happens next.

  • The blow prompt (BLOW) is the signal to give your sample. Wait for it before you blow.
  • The pass result (PASS) means you can start the vehicle.
  • The warning result (WARN (Alberta Only)) also lets you start the vehicle. This result exists in Alberta only.
  • The fail result (FAIL) means you can’t start the vehicle. Take a follow-up test as soon as the handset signals that it’s ready.
  • The violation result (VIOL (Violation)) also means you can’t start the vehicle, and the event is recorded for your monitoring authority.
  • The wait countdown (WAIT ##) is a short pause between attempts. After a fail, the screen cycles from FAIL to WAIT ## and back to the blow prompt.

The second group is the abort prompts. An abort means the handset couldn’t read the sample, so it asks for another try and records no result.

  • Blow Softer means too much air pressure. Ease off.
  • Blow Longer means not enough. Keep blowing for the whole test.
  • Don’t Inhale means air moved the wrong way, usually from blowing before BLOW appeared or breathing in close to the mouthpiece.
  • Mouth Closer means the handset isn’t seated against your mouth properly. Check that your mouth is fully on the mouthpiece and the handset isn’t at an angle.
  • Please Retry means moisture has built up inside, or the vent behind the handset is covered. Give it time, and uncover the vent.

An aborted test isn’t a violation. Retake the test once the screen shows BLOW again. A fail or violation result isn’t the end of the session. After any result other than PASS, take a follow-up test as soon as the handset signals it’s ready, and use the WAIT ## countdown to settle. Several aborts in a row can put the handset into a temporary lockout, which the next section covers.

Smart Start Code Meanings for Countdowns and Lockouts

A countdown is the handset giving you notice. These messages exist so you have time to reach a service centre while the vehicle still starts, and the length of that window differs from one jurisdiction to another. Your own monitoring authority (the Ontario Ministry of Transportation, Alberta Transportation and Economic Corridors, RoadSafetyBC, Saskatchewan Government Insurance (SGI), Manitoba Public Insurance or the Société de l’assurance automobile du Québec (SAAQ)) sets the rules that apply to your program.

There are three kinds of lockout: service, violation and temporary. A missed Service date starts a Service Lockout (SRVC / L ###) countdown, and reaching the allowed violations starts a Violation Lockout (ViolLck xxhr) countdown. Here’s how each one shows up on the screen.

MessageWhat it meansWhat to do
SRVC / L ### (Service Lockout)The number is the hours left before the handset locks because your Service date passedBook and keep a Service appointment during the countdown
LOCKOUT SRVC (Service Lockout)The countdown ended and the handset won’t take a testCall for an unlock code from inside the vehicle, then get to your Service
ViolLck xxhr (Violation Lockout)The allowed violations were reached, and the number is the hours left before lockoutGet to a service centre for a violation reset during the countdown
LOCKOUT VIOL (Violation Lockout)The countdown ended and the handset won’t take a testCall for an unlock code from inside the vehicle, then have the violation reset in person
IDLE 8:00Smart IDLE is running and rolling tests are pausedNothing, until the timer reaches 0:00, you start moving or you press #7 again

The third kind, the temporary lockout, has no countdown message of its own. It follows a pre-set number of aborted tests, before or after the vehicle starts, and the handset simply won’t accept a test for a short period. Use the time to drink water, take a few slow breaths and air out the vehicle, then test again when the handset resets. Leave the handset connected while you wait. Disconnecting it while the device is on is recorded as a violation.

The Service and violation messages work the same way. While either countdown is running, a passing test still starts the vehicle. Use that window to get to a service centre near you. The lockouts post walks through each way out in full, including what counts toward a violation lockout and how the count resets.

Before you switch off the engine, glance at the screen. If a rolling test is pending, finish it before you leave the vehicle. You can still complete one after the engine is off, but you’ll have less time and the handset beeps faster as it runs down. The horn also sounds once the timer reaches the halfway point, so treat it as a reminder.

The violation allowance and the length of each countdown are set jurisdiction by jurisdiction, so the same message can leave you more or less room in different programs. This table names who sets them and where to check the charges that may apply, if applicable, for each one.

Province or territoryAuthorityCharges and program details
OntarioMinistry of TransportationOntario program fees
AlbertaAlberta Transportation and Economic CorridorsAlberta program fees; the WARN (Alberta Only) result applies here
British ColumbiaRoadSafetyBCBritish Columbia program fees
SaskatchewanSGISaskatchewan program fees
ManitobaManitoba Public InsuranceManitoba program fees
QuebecSAAQQuebec program information; support is 1-844-282-8300
YukonDriver Control BoardYukon program fees
Northwest TerritoriesDriver and Vehicle ServicesNorthwest Territories program fees

If a missed rolling test or rolling re-test started the clock, the same logic applies. The device recorded the event, your monitoring authority sees the record, and your program decides what follows. Smart Start Canada can’t tell you whether an event will extend your program, because that call belongs to the authority.

Unlock Codes and the Call

When the screen reads LOCKOUT SRVC or LOCKOUT VIOL, the handset has stopped taking tests and the next step is a phone call. Dial 1-844-432-4776 (1-844-282-8300 in Quebec) from inside the vehicle, because the code is entered into the handset on the spot.

Image alt text: Driver on a phone call in a parked vehicle at dusk, with the interlock handset mounted on the dashboard

The automated phone system can give you the first unlock code in a violation or Service period without waiting for an agent. If you need more than one code in the same period, you’ll speak to an agent. The code lets you start the vehicle so you can reach a service centre. It doesn’t clear anything. The Service still has to happen, and a violation still has to be reset in person, with the driver, the device and the vehicle all at the service centre. It can’t be done remotely.

A charge may apply for an unlock code or a violation reset, if applicable. Fees vary by province, and each province has its own page. Ontario’s figures are on its program fees page, and British Columbia’s are on its own fees page.

A countdown is the cheapest time to call. If the screen is still counting, you can book the appointment through your account or contact the call centre before the window closes, and you never need a code at all.

Where to Find the Full Manual

Everything above is the short version. The longer reference is on the ignition interlock product page, which carries the SSI-20/35 and SSI-FLEX user manuals. The current handset has no hum step, so a sample only needs a steady blow. The number-pad answer is on the FAQs page, and your installation appointment included training on the screen.

If you haven’t yet had that appointment, read the manual first. The prompts are easier to recognize when you’ve seen them once before you’re sitting in the driver’s seat with a test pending. The device prompts you for a breath sample at random times while the vehicle is running, which is how Ontario’s program and British Columbia’s both describe it. The national guidelines for interlock programs give general context on how programs record device events. They don’t replace what your own authority tells you.

Smart Start Handset and Code Questions, Answered

What Does VIOLCK04DAY Mean on My Smart Start?

A ViolLck message with a four-day count is a violation lockout on the clock. Take the number as your deadline. Book the reset appointment today, and plan to bring yourself, the device and the vehicle. If your screen words it differently, phone the call centre and read the message out exactly as shown.

Why Does My Interlock Say Lockout in 4 Days?

The handset stops taking tests when that number reaches zero. The label beside it names the cause: a Service date that passed or a violation allowance used up. Pick up the phone or open your account today and book the visit while the vehicle still starts.

What Is the Unlock Code for Smart Start?

No fixed code exists, so there’s nothing to look up or save in advance. Each code comes from a call you make while sitting in the vehicle, after the screen reads LOCKOUT SRVC or LOCKOUT VIOL. An agent steps in only if you need a second one in the same period.

How Do I Reset My Smart Start Device?

Phone calls and account requests can’t clear a violation. A technician does it in person, with the driver, the device and the vehicle in the building together. If the handset has no power at all, call before anyone touches any wiring.

How Long Is a Lockout Code Good for Smart Start?

The code lets you start the vehicle so you can reach a service centre, and it temporarily extends the time to get your appointment done. The site doesn’t give a length of time, and it may depend on your program, so ask the call centre when you call for the code. Plan to book your visit the same day.

How Much Is a Smart Start Lockout Code?

A charge may apply, if applicable, and the amount depends on your province or territory. The fee is added to your account and handled at your next appointment. Check your own province’s program fees page, such as Ontario’s or British Columbia’s, for the current figures.

Image alt text: Smart Start Canada service centre technician showing a customer an ignition interlock handset across the counter

Smart Start Canada serves All Provinces and has completed 350,000 plus installations, with service centres in most provinces. If your handset shows something this page doesn’t cover, call 1-844-432-4776 (1-844-282-8300 in Quebec) and read the message out exactly as it appears. Your next step is on the FAQs page.

Disclaimer: This article provides general information only. Ignition interlock program rules vary by province and territory and change over time. Always confirm current requirements directly with your provincial program authority (the Ontario Ministry of Transportation, Alberta Transportation and Economic Corridors, RoadSafetyBC, SGI, Manitoba Public Insurance or the SAAQ) or Smart Start Canada before making decisions about your enrolment.